Farm Manuals Fast - John Deere Manuals - John Deere Square and Round Hay Baler Manuals - John Deere 348 Hay Baler Manual

John Deere 348 Hay Baler Manual


John Deere 348 Hay Baler Manual This product is on sale

Product Description

This is the operator's manual for the John Deere 348 rectangular hay baler. This manual contains information on operating, troubleshooting, and maintaining your baler.



Original Price:
$29.99
Sale Price:
$19.99 (Save 33%)


Purchase the complete set and save! Get an additional 25% off our manual bundles!

John Deere 348 Hay Baler Manual
John Deere 348 Hay Baler Manual
$19.99

Buy Both For Only

$37.49

Table of Contents

  • Safety
  • Preparing the Tractor
  • Preparing the Baler
    • Breaking in the Baler
    • Securing Jackstand
    • Positioning Tongue 
    • Attaching Hydraulic Tongue Positioning
    • Cylinder
    • Selecting Correct Twine and Wire
    • Loading Twine Box
    • Using Modified Square Knot-Sisal
    • Twine
    • Using Sheet Bend Knot-Plastic Twine 
    • Threading Right-Hand Needle
    • Threading Left-Hand Needle
    • After Threading Needles
    • Loading Wire Box
    • Threading Needles-Wire Baler
    • Selecting Proper Tire Inflation
  • Attaching and Detaching
  • Transporting 
  • Operating the Baler
    • Starting and Operating the Baler 
    • Preparing the Crop 
    • Selecting Correct Direction of Travel
    • Understanding the Tying Cycle 
    • Understanding the Twisting Cycle
    • Replacing Flywheel Shear Bolt 
    • Replacing Knotter and Needle Drive
    • Shear Bolt
    • Adjusting Compressor Rods
    • Removing Compressor Rods 
    • Adjusting Twine Tension
    • Checking Twine Strength
    • Adjusting Feeder Fingers
    • Adjusting Bale Length
    • Adjusting Bale Weight
    • Adjusting Height of Pickup Teeth
    • Adjusting Gauge Wheel Height 
  • Attachments
  • Lubrication and Maintenance
    • General Purpose Grease
    • Hydraulic Bale Tension Oil
    • Gear Case Oil
    • Alternative Lubricants
    • Observe Lubrication Symbols
    • Perform Lubrication and Maintenance
    • Chains
    • Lubrication and Maintenance
    • As Required
    • Every 5 Hours
    • Every 10 Hours
    • Every 10 Hours
    • Every 100 Hours 
    • Each Season 
  • Troubleshooting
  • Service
    • Bolt Torque Charts 
    • Placing Needles in Home Position 
    • Timing the Baler
    • Adjusting Bale Measuring Control
    • Crank Stop
    • Adjusting Knotter Drive Brake
    • Adjusting Needle Frame and Needle
    • Link
    • Adjusting Needle-Twine Baler
    • Adjusting Twine Holder
    • Adjusting Tucker Fingers
    • Adjusting Knife Arm
    • Replacing Knife and Wiper Plate
    • Adjusting Knotter Gears 
    • Removing Knotter Assembly
    • Replacing Billhook Cam 
    • Multi-Twine and Sisal Billhooks
    • Adjusting Twine Disk
    • Adjusting Billhook Tongue
    • Adjusting Needles-Wire Baler
    • Adjusting Needle Lift Link-Wire
    • Baler
    • Adjusting Wire Guides 
    • Adjusting Grippers
    • Adjusting Twister Hooks
    • Adjusting Bevel Gear and Pinion
    • Adjusting Intermittent Drive Gear-Wire
    • Baler
    • Adjusting Slip Clutch 
    • Adjusting Pickup Flotation
    • Adjusting Auger Drive Belt
    • Adjusting Bale Counter
    • Adjusting Plungerhead 
    • Adjusting Hydraulic Bale Tension Pump Chain
    • Adjusting Feeder Finger and Main Drive Chains
    • Checking Multi-Luber
    • Broken Oil Lines
  • Storage
    • Storing Baler at End of Season 
    • Preparing for Beginning of Season 
  • Crime Prevention Tips 
  • Assembly 
  • Specifications

Product Information

Pages:
126
Model:
348
Make:
John Deere
Manual Type:
Operator's Manual